top of page

Woodworking Tools

Carbide Tipped Circular Saw Blades

Have your carbide saw blades professionally sharpened and sent back to you. We sharpen 71/4" to 30" diameter carbide blades.

We sharpen all woodworking carbide tipped circular saw blades. Blades are precision sharpened to a 600 grit finish and in most cases are sharper after we sharpen them then they were brand new. We sharpen circular saw blades up to 30" in diameter. We do not repair or replace carbide teeth on circular saw blades. If you don't say we will go ahead and sharpen carbide circular saw blades with up to 3% of the teeth missing. We remove as little carbide as possible so that you get the maximum number of sharpening's out of any of your saw blades. After sharpening we check each blade for plate run out and tooth runout making sure both are no more then .005. You will always get back your own saw blades and not somebody else's. 

Carbide Tipped Saw Blades, Biscuit Cutters, Milling Cutters, Scoring Blades

We Sharpen Up To 30" Diameter Saw Blades

         ATB / FLAT             ATBR / TC
       $.30 per tooth          $.40 per tooth


7 1/4" Contractor Blades    $5.00 

Carbide Dado Blade Sets

Have your stacked dado sets professionally sharpened and sent back to you. We sharpen most all styles of dado blades. We need to receive both outer blades and all the chippers to the set you are sending, as they all need to be sharpened at the same time to properly sharpen them and keep them as a matched set.

Dado Blades and Chippers   - $.45 per tooth on outer blades and $3.50 per chipper

Planer and Jointer Blades

We specialize in precision sharpening of carbide and HSS planer and jointer blades. We flat grind these blades. Our primary goal is to provide our customers with the highest quality sharpening service possible, while also offering an unbeatable level of customer service. 

   Our experienced technicians use state-of-the-art equipment to bring your tools back to their original sharpness, while also helping to extend the life of your tools. We take pride in our commitment to providing the highest quality sharpening service available. We can easily sharpen planer blades up to 30" in length.

 

HSS Prices 

Single Edged HSS Jointer and Planer Blades - 1/8" Thick $.50 per inch* - 3/8" Thick $1.00 per inch* - 1/2" Thick $2.00 per Inch*

Double Edged HSS Jointer and Planer Blades -1/8" Thick $1.00 per inch* - 3/8" Thick $2.00 per Inch* - 1/2" Thick $4.00 per Inch*

Match grinding 1/8" $1.00 per inch - 3/8" Blades $2.00 per inch - 1/2" Thick $4.00 per inch

Carbide Prices 

Single Edged Carbide Jointer and Planer Blades - 1/8" Thick $1.00 per inch* - 3/8" Thick $2.00 per Inch* - 1/2" Thick $4.00 per Inch*

Double Edged Carbide Jointer and Planer Blades - 1/8" Thick $2.00 per inch* - 3/8" Thick $4.00 per Inch* - 1/2" Thick $8.00 per Inch*

Match grinding 1/8" $2.00 per inch - 3/8" Blades $4.00 per inch - 1/2" Thick $6.00 per inch

*(Minimum $4.50 Per Blade)

** Once we inspect your blades if there are any blades with nicks over 1/16" there may be a charge for additional grinding.

Other Woodworking Tools

Hand Plane Blades - We sharpen hand planes blade bevels at 25 degrees. If you prefer a different angle just let us know what angle you want your hand plane blades sharpened at. When put on a good sharp straight edge but it will be up to you to finish with your stones and hone/polish.  - $5.00 each

Wood Chisels - We can sharpen your chisels correcting the primary angle on your chisel with a primary angle of your choice 20, 25, and 30 degrees. Your chisels will come back sharp with a straight / square edge. It will be up to you to finish with your stones and polish. Just let us know what angles you want your wood chisels sharpened at. - $4.00 each

Brad Point Bits - $3.00 each
Forstner Bits HSS - $4.50 each
Hole Saws HSS - $5.75 each
Muiltispur Bits - $5.00 each
Wood Auger Bits - $3.00 each
Wood Lathe Tools - $4.00 each
Wood Spade Bits - $2.50 each
bottom of page